Peening Jigs and Anvils
Peening is the process for maintaining the correct tapered edge profile (bevel) of the scythe blade. This is achieved by hammering to thin the blade edge – rather than grinding on a grindstone.
Essentially there are two main methods of blade peening, each having its own set of peening equipment:
Jig Peening – using a peening jig
Freehand Peening -using a peening anvil and hammer
For more information and tips on peening jump to the FAQ at the foot of this page
I can arrange individual and group peening courses and tuition.
For more details see Help with Peening
I also schedule one or more peening courses each year – see calendar
Peening Jigs
Jig Peening – makes use of a jig to hold the blade in the correct position and control where and how the hammer blows impact the blade. The jig pinches the metal at the very edge of the blade which is then struck with a regular hammer blow to squeeze and thin out the metal. This arrangement is by far the easiest to master, and the approach I recommend as standard.
I have in stock two choices of peening jig to complement your scythe set:
Slovak Standard Jig – £30
These jigs are the budget option being half the price of the deluxe Fux jig. They nonetheless peen well and are perfectly serviceable being made from good quality steel, so will last (unlike some other cheaper jigs). I have been happily using one of these regularly for 10 years. They are cheaper in part because they often come out the factory poorly finished – but don’t worry I now quality check each one and polish them myself before selling them.
This is the choice of jig I recommend for light use, where you mainly have rough vegetation to mow (and don’t aim for such a fine edge), or if you plan to progress to freehand peening.
Austrian Fux Deluxe Jig – £90
This is a quality tool designed and made by the Schröckenfux Scythe Factory. This is reflected in the price.
I find that this Fux jig can produce a smoother more consistent peened finish compared to the standard jig, which I like. Some say “almost as good as freehand peening”. I do now use this in preference when jig peening.
This is the jig I recommend for frequent use and where use (and cost) is shared within a group. It is also a good investment if you plan to rely solely on jig peening (not freehand) for the foreseeable future and want the best results possible from this method.
Peening jigs are used with a regular hammer (not supplied). Most regular DIY medium weight hammers will do; they don’t need a special face finish as they do not directly contact the blade itself.
You will also need to set up a mount for the jig: a peening station – see peening stools and logs
Freehand Peening Set
Freehand peening – using a small anvil and dedicated peening hammer. This method is referred to as ‘freehand’ as the positioning of the blade on the anvil, and landing precision hammer strikes depend on the peener’s hand-eye coordination.
Freehand peening is a skill that has to be learnt and developed over time. I do not recommend this method to beginners, or without instruction as, unless you are already an accomplished metal worker, you will struggle with it.
It is however something to aspire to as it has the potential to deliver the finest results.
Freehand Peening Set – £84
I stock freehand peening anvils and hammers. These are best purchased as a set as both are manufactured by Picard in Germany from the same steel matched for hardness.
The hammer is of a good weight and balance for peening, and comes with the all-important polished working face (as any imperfections or damage to the hammer face, such as from banging in nails, will stamp impressions into the metal of your blade).
With tuition and experience freehand peening has the potential to deliver most control over the peening process and produce the best results. With practice experienced freehand peeners say they can peen a blade as quickly as with a jig.
I recommend starting by getting proficient with jig peening; then getting some freehand peening tuition; after this move to doing most of the initial profiling (back from the edge) with a jig, and just finishing the very edge with the freehand anvil (edge peening).
Even when you get fully proficient at freehand I would keep a jig in your scythe tool kit – especially for quick peens of rough work blades.
Peening FAQ
Peening is a metal working process of cold forging with hammer blows to reshape the metal and, at the same time, toughen the blade edge by work and strain hardening. For scythe blades the ultimate aim of peening is to achieve a very fine but resilient cutting edge profile- like a fine razor blade.
Peening is the best method for maintaining the correct tapered edge profile (bevel) of Austrian scythe blades.
Scythes need constant sharpening (honing with a whetstone) to work well with minimum effort. This repeated honing will in time wear back the main bevel to a point where it becomes thicker and bull nosed in profile, and as result increasingly hard to maintain a keen edge by honing alone. At this point the blade requires restorative maintenance to reprofile the bevel so it can be honed effectively once again.
The interval between peening will vary with mowing conditions and your whetstone. Coarse whetstones, rough ground conditions and mole hills (soil) wear the blade back faster than working with fine whetstones in soft lush grass.
The blade will usually benefit from peening after 4 – 5 hours of continuous mowing and honing. You can leave it longer, but field honing will become less efficient, and you may end up having to spend longer peening to restore the edge.
If you only mow an hour section of your meadow each day you may only need to peen once or twice week.
If you mow all day (8 hours) take a fresh peened blade out in the morning, peen it at lunch time, and peen again in the evening for the following day. Or, as I sometimes do, take two peened blades to the meadow: one for the morning and one for the evening.
Repeated honing with a whetstone gradually wears back the main bevel to a point where it becomes thicker and bull nosed in profile. You may notice that it becomes increasingly hard to get a keen edge using your whetstone. You may find you need to step up to a coarser more aggressive stone to get a sharp edge that will cut. You will also find that you need to hone more frequently as the edge quickly dulls. Inspection of the bevel profile, visually and with your fingers (carefully!), can be a guide to the state of wear back.
These indicators to some extent require the acquisition of knowledge and experience to assess. Do pay regular attention to your blade edge: feel and remember what it was like new or freshly peened, and what a blunt profile is like by comparison. Your observations and experience will develop your skill with time. If you think your blade needs peening, peen it, hone it, and if it works better than it did before then take note: it did need peening!
Peening is another skill set, which like scything itself, has to be learnt and developed.
Jig peening is the easiest method to master. It is possible to be self taught in jig peening from books and online videos; particularly if you have been on a ‘learn to scythe’ course and had the basic principles demonstrated to you.
Freehand peening is much trickier to learn. I strongly advise getting tuition in this method from a skilled and experienced instructor, rather than attempting to self-teach; unless you are already a confident metalworker.
Getting instruction will definitely help with either method. You will learn faster, with less frustration and fewer mistakes. Peening courses, as well as scythe events like ‘International Peening Day’ in April, provide opportunities for you to both lean the technique as well as compare and discuss your results with others.
Yes, the bevel can be reprofiled by filing or grinding. Traditional English scythe blades are reprofiled using a grindstone. For English scythe blades grinding is the only option as their metal is too brittle and will split if struck with hammer.
- Grinding removes metal vs. peening which preserves metal.
- Peening strengthens metal vs. grinding does not, or may weaken metal if overheated
- Peening shapes the profile of the bevel vs grinding can give a hollow ground profile with the right equipment
A chain saw file (as supplied with the sets) can be used as a rough and ready method for filing back the bevel profile to a shallow angled taper. This method can produce adequate results particularly for rough mowing and weed bashing with a ditch blade.
Grinders and power sanders can be used, but be very careful not to overheat and burn the metal as the delicate edge will lose its strength. Low speed tools are safer, moving constantly to avoid hotspots. Water cooled grindstones are best (but expensive): the water keeps the blade from heating, and the curvature of the grindstone can impart a hollow ground shape to the bevel.
If you approach peening thoughtfully and carefully, and ideally with some instruction, you should not cause any damage to your blade that cannot be repaired quite easily.
Overzealous peening: using a too heavy hammer, or heavy blows, can result in ‘over-peening’ damage. The symptoms of this are flaky-thin bulging edges and small (hopefully) cracks along the edge. The simple remedy for this is to file back the damaged sections with a chain saw file (as supplied in sets), and try again. Monitor and keep checking your results as you are working so you stop before these faults appear. If you notice just occasional mild symptoms affecting small sections of your blade, you can usually manage through these as they will work out with whetstone honing, and should not affect the performance of the blade too much. Just keep monitoring any cracks to see they do not get any worse and need repairing.
Peening too deeply into the blade, landing hammer blows more than 4-5mm back from the edge, may result in deformation of the blade into ripples (wavy rather than flat). This is more difficult to cure. One of the main benefits of the peening jig is that it fixes the blade so that the pinch cannot occur too far back. It is more of a risk with freehand peening.
Not holding the blade flat on the jig or anvil can cause deformations of the edge. The edge may curl up, curl down or get rippled. Re peening with a corrected positioning can usually remedy these faults.
Do constantly monitor and check your work as you peen to spot errors and correct them before they get any worse.

